• Important: Delayed Conduction in Bucking Coils

Important: Delayed Conduction in Bucking Coils

  • Topic Is Sticky
  • Topic Is Locked
  • 16K Views
  • Last Post 24 February 2024
Chris posted this 11 March 2019

My Friends,

The Effects of Delayed Conduction in Bucking Coils is important. What is Delayed Conduction? What is the point of this?

Delayed Conduction is specifically to get the Voltage on the Terminals of your Partnered Output Coils as high as possible in reason! Its the change in Magnetic Field that Creates Voltage, its the Opposition of Magnetic Fields that Pumps Current! 

Circuitry can also be employed to delay Conduction on the second Partnered Output Coil.

Ref: How to build your own Above Unity Machine

 

I gave an example of Delayed Conduction here.

As you can see, the Mosfets will only conduct when the Zener Diodes Conduct, this is rated to 18 Volts.

This means, the ends of the Partnered Output Coils must be at least 18 Volts, before the Coils can power any load!

We have seen this before! This is not new to those that have done the Study!

 

 

The MEG Demo Circuit

Where D2 represents a Bi-Directional TVS.

 

Ref: JLN MEG Replication

 

Ref: The MEG Team Data.

Where the Top Trace represents the Input Channels, and the bottom Trace Magnetic Resonance in the Output Coils, seen as Asymmetrical Regauging.

 

NOTE: JLN used a MOV in his MEG Replication. A MOV has similar Voltage to Current Characteristics! 

 

Ref: JonRB

 

 

Ref: Renesas Datasheet

 

 
Ref: The MOV or Varistor V I Characteristics

 

 

 

I want to stress the point of getting the Voltage on the Terminals of your Partnered Output Coils to a maximum without being disturbed. Input Creates a Voltage on your Terminals, then the Input is switched off. Then your Partnered Output Coils Conduct and we Pump Current.

Remember: Some of these Circuits may require an Earth Ground.

   Chris

Order By: Standard | Newest | Votes
Chris posted this 11 March 2019

My Friends,

What I am sharing is critical, extremely important Information!

Magnetic Resonance is seen at a specific Frequency and a specific Duty Cycle. This is a specific characteristic of the Coils, Induction and so on. Lots of turns means low Frequency, few turns means higher Frequency.

When you catch the Wave, you will know, trust me!

Monitor your Currents, you will see, equal and opposite. You will see the Sawtooth Wave form also, seen above and shown many times on this forum!

Bucking Coils, Pumping Current, the effects of Magnetic Resonance are truly amazing. Brute Force for free, a little tickle under the chin and the Machine does the rest for you, a Pump, like the Hydraulic Ram Pump, shown many times also!

Simple Starting Circuit - Some parts upside down to make you think backwards.

Where: D1 is a Delayed Conduction Device, Zener Diode and a Mosfet or a MOV or a TVS or similar device.

 

I really want to encourage all here to share your work, this works!

This is very important! A critical point has been reached and I need all members here to direct their attention to this topic for a little while?

Please?

We truly are Light Years ahead of the other forums!

   Chris

Chris posted this 12 March 2019

My Friends,

On the: 30 July 2017, I placed the thread: Timing, here for a reason. I made specific focus on the interactions of the Coils and how the Coils were used in specific ways, to reduce Transients, in the form of Common Mode Noise, almost entirely!

I asked you to think about ways to reverse the situation, saying: "You need to let the System Breath, bring it to life!", now, today, I have shown you how important timing is! What is possible with timed Electromagnetic Wave Interactions!

I ask you, do you see a pattern? Do you see what I am doing? Do you see how much planning and work this has taken?

Aboveunity.com has changed the world! We are light years ahead of the other forums! They have been left in the dust! Redundant, effective immediately!

We have made the world a better place, and we don't plan to stop here! Support us, help us, this train ride has only just begun!

   Chris

Jagau posted this 12 March 2019

Hi Chris

I noted that there was in addition to frequency and duty cycle a third extremely critical adjustment,

the power level of the mosfet gate,  for my circuit this has completely change the results.


I do not know if for others you have noted the same results ??

Jagau

Chris posted this 13 March 2019

My Friends,

I want to share again:

 

The same rules apply as I have shared in the thread: Parallel Wire or Bifilar Coil Experiment which was a very important introductory thread!

If you learn and understand what I am trying to share in the video, then catching the wave will be the only thing that takes a little fiddling!

   Chris

 

P.S: This content I am sharing with you, you will not find anywhere else in such detail. I ask you, save and share this information. It is very important!

Jagau posted this 14 March 2019

 Its the change in Magnetic Field that Creates Voltage,

its the Opposition of Magnetic Fields that Pumps Current! 

Hi Chris 

This is words of wisdom too

Jagau

Wistiti posted this 12 March 2019

I will build something base on this concept you share my freind and will share it with all on the forum.

For now my spare time is limited but as soon as I can, I will prioritize this one.

Thank you for sharing!

Chris posted this 12 March 2019

My Friends,

@Wistiti - Thank you my Friend.

What to look for is, at the time of Delayed Conduction, is a Standing Wave of much Greater Potential:

Ref: https://youtu.be /cQWLP6k-c7I

 

A Naturally Simulated Effect, one in which we need to simulate in our Electromagnetic Waves! This causes the increase in Magnetic Resonance, it can be much greater than the original Wave input! Then of Course, we hold Conduction, the Wave dissipates and we have much greater Energy Output than we input!

This is the: Waves Slapping Together.

 

 

We saw an example of how this can work here.

   Chris 

Chris posted this 12 March 2019

Hi Jagau,

My Friend, yes, there is a little fiddling. Once found the results are very prominent. Its not hard to miss once one knows what to look for! Problem is, very few know what to look for!

Yes you're right, slowly turning up the input power and one will soon find the Conduction Power required. wink

Fantastic work my Friend!

   Chris

Chris posted this 15 March 2019

Hey CD,

I agree, yes there is an element description!

I am not convinced Graham's MIT was in Saturation. I think maybe close, but the problem I see is, if he was in Saturation, the Voltage and Current Waveforms would not be 90 Degrees from each other:

 

Input Voltage ( Yellow ) and Input Current ( Blue ) would be almost in phase, not a quarter Cycle later. A Quarter Cycle is 90 Degrees and indicated the Core is not Saturated.

 

So, at Saturation, Inductance is lost, and an LC Resonance Tank Circuit can not be 90 degrees out of phase. The Inductor becomes a Resistive Element, because it has lost all its Inductance L.

Sorry, long winded, but my analysis, is that he is not in Saturation, but is close. I may be wrong and over looked something?

Graham has an interesting machine, yes it is directly related to this topic! But it is done in a slightly different way.

Grahams Partnered Output Coils, should be thought of as two Parallel Wires! Connected in Parallel Series! The Wires have a direct relationship to each other! At anytime the Relationship to each other were to change, so would the Magnetic Fields between them.

Remember, Current is the Magnetic Field!

If the Current between the two Parallel Wires, were to be aloud to change, then there would be a full reversal, which we have seen already. Why a full reversal in Current? Because it must be Equal and Opposite, Faradays Law of Induction with Lenz's Law states this!

This Change, only requires a change is the flow of Current, which is a Conduction related issue!

Break up all the parts of the Cycles seen:

 

The Area marked in Red is standard Transformer Induction, there is no indication of any overly unusual activity in this region. This region is the Half Cycle, it could be thought of as a negative DC half of the AC Cycle. Power here from Input to Output is Transformer Induction, with losses. The power would look like this:

 

Marked in Yellow.

Now, marked in Green, the active part of the Action comes:

 

The power would normally look like this:

 

 

Marked in Green. Now we must carefully analyze this, because we only have half of the Power expected, we have a specifically arranged interruption in Conduction at Peak Current, or very close to it.

 

The Switch:

Important: The Green Trace is the Output Current shown on only One wire:

 

At the point of the switch:

 

Marked in Red, the point of the Switch! Also seen, and should be noted, the only kick in the waves seen:

 

Marked in White, the only kick in the waves seen. Its a negative Kick, a kick that shows a negative pressure on the Input Current ( Blue ). Also important: The Input Current, after the Switch, the amplitude increases over time!

 

So, what's going on?

  1. Parallel Output Wires are building in Voltage and Current, the are fully loaded up until the Switch!
  2. At or close to Peak Current, the Parallel Series Connected Coils are Interrupted, the Conduction on One Coil is Broken...
  3. What happens now? How can the Current Flip so quickly?

 

 

The Green Trace above, shown above to indicate the Positive ( Red ) and Negative ( Black ) swings in the Output Current Trace.

Seen in the middle, is the very sharp change from Positive ( Red ) to Negative ( Black ). This happens in a very short time!

The Coils have a Tension, then the Tension in one Coil is broken, via a switch. One Coil still has a tension, but the other has no current, but the other coil wants to change. The Tension in this coil can not stay where it is.

The Coil that has a broken tension, is conductive via the Mosfet's Internal Diode, but only in reverse. We know that Equal and Opposite Currents must start to flow if there is a Conduction Path! 

Question, does the Switch need to be turned back on? If so why?

Graham is using the Tension ( Voltage and Current ) on one Output Coil, to Flip the other Output Coils Polarity, to create equal and opposite Tension ( Voltage and Current ). Bucking Coils! He is using Partnered Output Coils!

Well, we have a reasonable post, nearly out of words...

   Chris

 

P.S: Bad images, sorry, I tried to find the best I could but they are not very good for what I am trying to show.

Chris posted this 18 December 2021

Hello Scalarpotential,

The Core is a Lenz, all it does is Focus the Magnetic Flux and the "Change" of this same Magnetic Flux, in Time ( t ), with a Propagation Delay.

So, the Core must be seen for what it is, having "Aspect Ratio" and thus Time Delay:

Uniform space has only two parameters:

  • 1: aspect ratio.
  • 2: time delay.

Aspect ratio defines the shape of energy entering a given region of space, but not its amplitude. Velocity or length define the time during which the properly shaped energy can be accommodated by a region of space. Aspect ratio is really a definition of the relative compatibility of adjacent regions of space. Does flowing energy current largely travel unimpeded through an interface, or does it largely reflect at the interface? Space has quiet zones through which energy glides virtually unreflected. There are also noisy zones where energy current becomes incoherent, bounces about and splits apart. Noisy zones in space have either rapidly changing geometry or rapidly changing impedance

 

Aspect Ratio, This is the Core Material, the Energy is Magnetic Flux, or The Magnetic A Vector Potential, which is Amperes per Sq Meter. One Gauss = 79.77 Amperes per Sq Meter.

No, ALWAYS there must be a Bucking, Opposition of Magnetic Fields! But in Order, there is an Order to the Action Sets!

Magnetomotive Force ( M.M.F ) is measured in Units of Current ( I ) and Turns ( N ), which is Ampere Turns ( NI ) and H is the Magnetic Field Strength, which is different again, but measured in the same Units, NI:

magnetic field strength, also called magnetic intensity or magnetic field intensity, the part of the magnetic field in a material that arises from an external current and is not intrinsic to the material itself. It is expressed as the vector H and is measured in units of amperes per metre. The definition of H is H = B/μ − M, where B is the magnetic flux density, a measure of the actual magnetic field within a material considered as a concentration of magnetic field lines, or flux, per unit cross-sectional area; μ is the magnetic permeability; and M is the magnetization. The magnetic field H might be thought of as the magnetic field produced by the flow of current in wires and the magnetic field B as the total magnetic field including also the contribution M made by the magnetic properties of the materials in the field. When a current flows in a wire wrapped on a soft-iron cylinder, the magnetizing field H is quite weak, but the actual average magnetic field (B) within the iron may be thousands of times stronger because B is greatly enhanced by the alignment of the iron’s myriad tiny natural atomic magnets in the direction of the field.

 

H is the Magnetizing Force, and not Magnetomotive Force, where, the Strength of the Magnetizing Field ( H ), and the mean length ( L ) of a solenoid are equal to the M.M.F. M.M.F = HL. So they are different things.

At Magnetic Resonance, the Core serves as a Medium, if you like a Transmit and Receive Medium, which facilitates the Coil to Coil Interactions required, but the same can be achieved with No Core also! So a Core is not necessary at all, I have found a Core can make results more fruitful in most cases.

At Resonance, we find Maximum Amplitude in Output Voltage ( V ) for the Minimum Input Current ( I ). Magnetic Interactions are at the same Propagation Delay, and no longer or shorter. An ideal, lossless Transformer becomes a realisation and Energy Gains come from the Time Domain.

Imagine Magnetic Resonance as a Shaft Driven "Generator", Speed Up, or Slowed Down, to find the Ideal Magnetic Interactions between the Rotor and Armature Coils. In measuring this, one would find 180 Degree Phase between each Coil, and approximately the same MMF Amplitude. At Magnetic Resonance, Shaft Torque would be at minimum, just like the Timing in a Combustion Engine. An Engine with Advanced or Retarded Timing does not run smooth and thus is not as Efficient!

The same is true of these Magnetic Interactions!

Best Wishes,

   Chris

Chris posted this 14 March 2019

My Friends,

This thread is so important!

I would like to emphasize the necessity of catching the wave. We have seen four examples of this:

I have shared one of my experiments also: Here

My Friends, I really want to stress the importance of patterns!

  • All of the above have one thing in common, the threads have the tag: Above Unity
  • All of then showed the Sawtooth Waveform!
  • All of them had very clear Energy Gains using Magnetic Resonance.

 

The Sawtooth Waveform

We all should be very familiar with the Sawtooth Wave form! I have been showing it for months now. It is very important that the understanding of how this waveform is achieved! Like I have tried to explain, this is where the Waves Slap Together, the Electromagnetic Fields of each Partnered Output Coil.

 

The Partnered Output Coils react together to Generate Energy. Using Delayed Conduction to achieve a Resonance in the Coils, called Magnetic Resonance!

 

Don Smith:

 

The MEG Team:

 

 

Tinman (Bradley Richard Atherton):

 

 

 

Graham Gunderson:

 

 

The Sharp Spike is Delayed Conduction, it is where the Two Partnered Output Coils have Magnetic Interactions that slap together very fast!

It causes a high Voltage, we hold the Conduction and the Magnetic Fields decrease linearly:

 

The Magnetic Fields slowly decrease to Zero, Equilibrium.

 

 

If you do these experiments, and have the patience to work together with us to the end goal, then you truly will have a self running Energy Machine!

 

@Jagau - I am glad that helps!

The fundamental magnets have been broken free of their binding forces which constrained them to be steady-state single pole uniform magnetic flux devices. They are now able to simply support mass, as demonstrated with the transformer steel illustration. They can now easily be made to adopt a dynamic motional field by applying a tiny amount of excitation. Specifically, 10V @ 1 mA (10 mW) of excitation at 60 Hz. will enable the coils of the triode to receive from the Dirac Sea in excess of 5000 watts of usable negative energy; how much more can safely be removed has not yet been determined.

Ref: Nothing is Something

 

Jagau, the above quote is nothing about the Magnets! Its about the Magnetic Fields! It reads wrong, there is an effort there to deceive, to miss-lead others!

The dynamic Field is Magnetic Resonance between the two Coils, actually Floyd Sweet used two sets of two Coils. Yes it is excited by a small amount of Power, because at Magnetic Resonance, the Coils feed back Energy to the input.

How this should read:

The fundamental magnetic fields of the Coils have been broken free of their bound force which constrained them to be steady-state single pole uniform magnetic flux source. They are now able to simply support mass, as demonstrated with the supporting Current demonstration. They can now easily be made to adopt a dynamic motional field by applying a tiny amount of excitation. Specifically, 10V @ 1 mA (10 mW) of excitation at 60 Hz. will enable the coils of the triode to receive from the Dirac Sea in excess of 5000 watts of usable negative energy; how much more can safely be removed has not yet been determined.

 

By changing only a few words, its now got a hugely different meaning!

   Chris

Jagau posted this 16 March 2019

Very good analysis Chris

As can be seen everything happens when the little kick occurs, the output current (green) is then ahead of the input.

 This happens when both current go through the most negative point.

Perhaps this is due to the timing of the 2 mosfets, there must be this special timing

that makes one of the two resumes the pendulum to project the ball further? An analogy of the swing?

as if it would be the capacitor who would take the lead

jagau

Jagau posted this 20 March 2019

It seems that the Synchronous rectification is very important for Mr Gunderson
This image is worth a thousand 

especially that of the center

Jagau

 

Chris posted this 07 April 2019

My Friends,

A video to further explain the Importance of this thread:

 

I hope this helps!

   Chris

Chris posted this 26 May 2019

Hi Atti,

The MEG has been independently replicated, by many, some are successful, some are not. This is the case with so much of this Technology! It is a required Study to understand what to look for! When you know what to look for, then your chances of Success increase many times!

My Post about the black Sun, it is very important!

 

 

An Accelerating Charge, which is exactly what we are doing, Accelerating Charges, and have a Sawtooth Waveform, which is what we do, when the process is correct. This important process is where Electrical Energy Increases can be seen.

Ref: www.youtube.com / watch?v=oH7WRKglKNk

I want to stress:

The Black Sun is an esoteric symbol dating far back into antiquity, petroglyphs have been found in the Americas of this ancient symbol that has been mainly known for its placement in the floor at Wewelsburg Castle by the SS of the German Reich. It is an esoteric concept rather than an actual object and like all esoteric symbols it represents knowledge, the more knowledge you have the more of the symbols secrets you unlock and the amount of knowledge needed to understand esoteric symbols can border on staggering for the uninitiated at times since the knowledge and science they represent is not taught outside of esoteric circles for a reason, in fact in almost every instance what people have been taught is the exact opposite of the truth. I have compiled a number of videos and made some myself I will provide throughout the article after a brief introduction of some of the concepts this symbol represents.

Ref: esotericawakening.com/esoteric-meaning-of-the-black-sun

 

I cant help think that we Humans are on a Crash Course. We have little hope in this world of a Free and Prosperous Future with interfering forces that interfere with us of a Negative Nature. This truly frustrates me! It seems we have gotten ourselves in a Hole and cant get out!

The price of Living increases everyday and is nearly out of control for many struggling families. When it truly should be the opposite, we should live in the cheapest times ever, we have the Technology, we have the power, we just don't have the Govern!

I do what I do with the hope, that in time this will help others, give a guiding light when there are so few in this world now!

Even though I have had some donations, much cost to host and provide information comes at a cost to me.

I only ask that readers and those that wish to follow, do the homework and do the required study!

Please do your own research, please study the most basic things that many would over look. Please understand this knowledge!

   Chris

Vidura posted this 21 September 2019

Hello All.

Here an experiment which I have performed inspired by the latest video about magnetic resonance. I have often the feeling when experiments failed, that it was related to the coils. Often I just have made them in hurry, not accurate at all. So this time I took the time to perform a proper tuning of the selfresonant frequency of the POC set. First I tested each of the coils individually on the core, with both coils together it becomes more tricky I found. Then I started to remove turnes from the one with lower frequency, until both had the same selfresonance:

For the individual tuning I attached only the positive output of the SG to the ground of the scopeprobe, in the final test with both coils the positive of the SG is attached to one coil, which acts as antenna, and the scope to the other coil.

Here the video of the experiment on delayed conduction:

Vidura

Chris posted this 16 March 2019

Thanks Jagau,

I posted another post also, a second one, but deleted it because I was not happy with it. Third party Circuit analysis is not my strong point, and I only want to post what I am pretty confident about.

Part of my post was about the "timing of the two mosfets" you point out. But I am confident my last approach will confuse others and make this harder to grasp.

One day, I believe, we will grasp so much more, Just Voltage and Just Current, the relationships of them, I believe is a small part of the Story.

 

Let me try again:

 

My Friends,

In the Terminals of the Left Partnered Output Coil:

 

 

Using the High Voltage Probe across the Left Partnered Output Coils Terminals, shown above, gives this Waveform:

 

 

Conduction is Broken for a very short time! Graham said around One Millionth of a second in the video? We have seen the Flip in Output Current on the Output from the Right side Partnered Output Coil:

 

 

The Same Time Base is used on the Scope. Note: M = 4μs

I guess, what I am trying to show here, is the Delay in Conduction of Graham Gunderson's Partnered Output Coils! His has done very much more like we saw here. The MEG, a  little different, I showed a slightly different way again here.

At the end of the day, its all a Delay in Conduction all achieving the same end result: Magnetic Resonance.

   Chris

Chris posted this 18 March 2019

Hey Jagau,

Apparently drawn by Graham at the Conference for Reiyuki. 

Graham drew the same diagram here:

 

He used the term Mosfet in the video.

Hope this helps some.

   Chris

Chris posted this 19 March 2019

Hey Jagau,

Isn't it silly how many symbols we have for the same thing:

 

MOSFET - Metal Oxide Semiconductor Field Effect Transistor

Ref: www.electronics-notes.com

 

I agree, if we don't learn something every day then perhaps the day has been wasted?

   Chris

Chris posted this 19 March 2019

My Friends,

To re-cap:

The Partnered Output Coils have three things all going on in time:

  1. A High Energy Field is created around the Coils: Shown as Power P.
  2. There is a timed Disconnect and Re-connect: Delayed Conduction.
  3. The Coils Fields ( Currents ) React in such a way to Slap Together very fast.

 

 

We have enough evidence above to say this is exactly how the Output was achieved! Don't forget the Wave:

 

This is what's going on between the Partnered Output Coils:

 

The Question is: Are all other devices working on the same principles?

The answer is: Yes, almost exactly the same!

   Chris

Chris posted this 22 March 2019

Hey Vidura,

Yes you're right. 33% is divided up like so:

 

So we see, 33% each:

  • Red
  • Orange
  • Blue

Of course, a normal H-Bridge is 50% to get an RLC Tank Circuit to resonate. Graham Gunderson's MIT is a special case requiring Off Time, this Off Time just happens to be 1/3rd of the Cycle.

Where we see Off Time, we see an increase in Current amplitude:

 

 

Of course, this is a significant indicator that the Output Coils are feeding back Energy to the Input. Feed Back as Floyd Sweet told us.

There is so much information in these scope shots, much I have covered here that you will not find on other forums! We truly are Light Years Ahead of the other Forums!

   Chris

Chris posted this 30 April 2019

Hi my Friends,

Well, a distraction, goal achieved, one down on me.

The following, simple, cheap, circuit, controls the speed of a 2000 Watt Vacuum Cleaner:

 

 

From Full Speed, to less than half speed approximately. The simple Circuit:

 

 

There is beauty in Simplicity. Blue is Mains Neutral, Brown is Mains Hot, or Active Line. Red is Motor in and Motor Out. The waveform:

 

 

The same ideas apply, the same triggering applies, Delayed Conduction, this is one mechanism. And, its important!

   Chris

Atti posted this 01 May 2019

Hi everyone.
I was curious about how a phenomenon develops.
How the power of the recorded current may decrease as the same secondary voltage. Or more.
It is related to my own thoughts and my own experiment.

But I mix another topic now. You must have remembered Tinman's rotating transformer. I know Chris did the experiment. You say what you think.

A similar theory is not a motor but a transformer. Therefore:
-Only with a self-closing oscillator, the demonstration works!
If you observe Tinman's rotating transformer, its speed (frequency) will also change.
-The load also affects.
-Reduced Frequency (TL494, SG..555) does not have a decrease in current strength. I tried it almost everywhere.
-No, it's not due to demagnetization.
- Even if the secondary side load is a half-wave diode or graetz bridge.
- Even if the secondary roll consists of a row.
- Only if we use the Chris layout.
-The load must be pulse-like in the Chris coil arrangement. Think of Mr Preva's experiment.
-Maximum 20% may be the fill factor.

I must have been wrong in many places!
I did this experiment quickly with the existing materials. It was not necessary to prepare for this purpose. Once again, it's just a demo to examine the effect. I think there is no special magic or the like.

I trust that the translation is understandable.
I will continue.

Chris posted this 05 May 2019

My Friends,

I would like to introduce a way of thinking, that may advance your thinking tremendously, if you have not already begun to adopt this idea.

A Potential, or a Voltage is a difference from one point to another.

When dealing with a Wire, we have an Insulated Conductor that has one Terminal at one Potential and another Terminal at a different Potential.

We measure these differences in Potentials on our Oscilloscopes:

 

 

 

All pretty simple so far!

 

Now, If we look at Harmonics, what do we see? We see what is termed Distortion. A very important word Distortion, because this is not actually a correct term for what is occurring!

Lets look at this waveform:

 

 

 

A rough analogy of occurrences and Interactions between waveforms. The Green waveform is showing what is termed as Distortion. Normally Distortion is something that is recommended to avoid. It is drummed into engineers minds all through their training, textbooks and lecturers repeat this continually, its almost like a type of brain washing. Repetitive Suggestion.

We must stop and ask ourselves what's really occurring? What is truly occurring?

What is occurring is Superposition of Potentials in Time.

 

 

We have covered Superposition many times, so at this stage the penny will drop!

How?

We have a Voltage that is "Generated" that is in the reverse direction, so on the Green line, we have a Dip, at the peak, this is directly related to the Purple trace, which has a phase that is approximately 180 Degrees out of phase to the Green line. So if we were to take a simple 1 + -1 equation then we loose amplitude at this particular point in time.

We have Harmonics, ONLY because we have "Generated" Potentials, and thus Currents must flow, in a direction that can be subtractive to our Source! This is critical to see.

"Generated" Potentials, which can be additive or subtractive depending on the Harmonic we are looking at:

 

 

An example of harmonics, were we can see relationships. For example, 1/2 is directly in the middle of the first waveform, called the Fundamental normally.

Why does the Wave on the beach Slap so hard into the Incoming wave? Because there is a relationship to the Fundamental that "Creates" a larger Fundamental, remember Tom Bearden's video?

 

 

 

What did he say: "A larger Fundamental" so how does our wave Relationship work?

Two wave forms in, to make a larger Fundamental, well, again, we have seen this, on the beach:

 

 

 

The Timing is the Relationship, the Wave are the Actions, together, they can create a larger Fundamental!

So, by using Delayed Conduction, we introduce our Second Wave Form, this is the Timing part, where the Delay in Conduction creates a Second, not normally present, which is considered to be a Harmonic, and engineers are told to avoid, Waveform that does the very same Slapping together with the First Waveform, creating the larger Fundamental.

The entire Machine is Non-Linear!

The Coils and the Timing of them are Non-Linear!

The Switch to create the Delayed Conduction is Non-Linear.

The Load is Linear, as a load can be.

So, I ask you to think on this! Its important! Its the Actions in the Machine, we are creating a Non-Linear operating Machine. There is no Magic, its simple, its just a case of following the very simple rules I have laid out, I have taken a long time to learn this and to lay it out in a way I hope others can understand.

   Chris

Chris posted this 09 May 2019

Hey Patrick,

You're not poking a sleeping dragon.

There is a little fiddling to this, I have said this before. Do not fear, because a clear focused mind can easily work out what's going wrong. 

  1. Your Input is a Frequency around 200Hz with a 10% Duty Cycle?
  2. Your Input Voltage is around 2 - 10 Volts?
  3. Your Input to Output Ratio is around 1 to 3?

 

What Circuit are you using on the Output for Delayed Conduction? Do you know for sure your Delayed Conduction  is triggering properly? Do you know the Time Constant is not changing to much on the Delayed Conduction?

  1. Starting with Open Conduction!
  2. Finishing with Closed Conduction!
  3. Cycle repeating?

 

You have a variable Frequency and Duty Cycle Equipment? Its important to tick off all the simple requirements! We need to follow the basic requirements or we are just wasting our time tongue-out.

You have the Potential up in the Core?

I want to repeat myself, The MEG Team used a TVS Across one Output Coil. They tuned the Frequency and Duty Cycle to the optimum Point where the Triggering of the TVS was sufficient and additive to the actual Magnetic Resonance point. Be prepared, The MEG Team found their Magnetic Resonance at somewhere like 31Khz.

Machines vary, I can not predict a Machine, it all vary's, with Core, Coils, Wire Type, the whole lot makes each machine very difficult to be able to predict!

The MEG Team have shared this with all of us already, as has JLN, as have Graham Gunderson, as has Don Smith, as has many other researchers finding the same amazing Effects!

Today, we have unique opportunity, we have the Data, we have the Results, we have mammoth amounts of Research Data, and I can tell you, this does work!

Only Liar's, Cheats, Bad Experimenters and Paid CIA Trolls tell you the opposite! This DOES work, when you have found the right conditions.

   Chris

Chris posted this 01 June 2019

My Friends,

The RC Time Constant is the Resistance ( R ) in Ohms multiplied by the Capacitance ( C ) in Farads, which is equal to Time ( t ) in Seconds.

 

So, t = RC = 1 Ohm x 1 Farad = 1 Second.

Now, I want to point a few simple things out. Akula published several schematics, where the Transistor was set with a Resistor and Capacitor to the Base to Emitter or Gate to Source for a delay:

 

The Combination of Resistance and Capacitance can delay the switching in of a Transistor / Mosfet:

 

So, if you have 180 degree signals and need to delay one, ever so slightly, this technique can be employed! Don't forget, you need to trick your Second Output Coil to Assist the Primary: Magnetic Resonance. So you need to delay the signal only a tiny amount: 0.000001 approx., or so seconds:

I have given the processes of Power "Generation" it simply is 1, 2, 3:

  1. Input - Frequency and Duty Cycle tunned for Magnetic Resonance.
  2. Secondary CoilOne Conducts Current, powers a Load.
  3. Secondary CoilTwo is switched in ( Delayed Conduction ), in such a way to Assist the Primary ( Magnetic Resonance ( Mr Preva Style ) )

Ref: Urgency Required!

 

Please remember those before us:

An alternate explanation for the current gain in the UDT is to consider each secondary winding as acting as the primary winding for the other secondary winding when an output current is drawn because the two secondary windings generate geometrically opposing fields.

Ref: Paul Raymond Jensen

 

I hope this helps some in moving forward in the direction of Delayed Conduction!

   Chris

Fighter posted this 17 June 2019

A laminated Iron Core with no Air Gap can not release the Magnetic Field! A Nanocrystalline Core can! A Ferrite Core Can, some Powdered Iron Cores Can.

From the Top of the Sawtooth Waveform, the Linear decrease in time, is simply the decay in Magnetic Fields. So, if the Core can not Decay, then you can not achieve the end result. From the Red Arrow to the Blue Arrow:

 

 

Chris is right, this is exactly what my device (I named it ZPM - Zero Point Module, as the free-energy units from Stargate Atlantis) does now:

I'm using a Metglas AMCC-200 core with bucking coils but without any permanent magnet.

Edit: Please be aware of the fact that depending on your core and your coils characteristics this phenomenon is appearing only in a specific frequency range; you will need to find that frequency range and fine-tuning it in order to find the optimum performance of your device.

This is how I search for the frequency range where the phenomenon appears and then fine-tuning it for my device to find the value where the input from source is minimum (most specific minimum value in mA):

getreal156 posted this 17 September 2019

Hi Cris,

Maybe I was not really clear. I'm actually working on the exact same circuit you are proposing and I'm experimenting with delaying alternatives for D1. This can be a Zener, a MOV or a combination with a mosfet. 
I tried CD's setup but I'm also experimenting with different delay circuits using a mosfet and zener. Like I mentioned the mosfet is blowing up. They probably fail due to high voltage spikes on the gate. 

ps.
Don't worry Cris, I'm a devoted follower of your work and this forum. I'm literally reading and analyzing ALL the posts and information here . I'm not an ee but I do have sufficient electronics skills and I believe that I understand the concepts and theories, as you have presented, quite well. The only problem I have is a lack of time for experimenting. Full time job, family with small children and only 24 hours in a day.

Chris posted this 21 September 2019

Hey Vidura,

Excellent! Thanks for sharing!

I left a message:

+1 Beautiful Vidura! The Voltage on the Varistor is showing the Work Cycle, a Linear decay over time of the Voltage, @3:54, the decay is not an exponential, its linear.

 

The Linear decay over time indicates you have the very same effects as Asymmetrical Regauging, this is the Work Period, you're using your Partnered Output Coils to pump Current, Electrical Energy, V x I over Time.

You show the importance of your switching tool, it is so extremely useful!

For all:

Floyd Sweet used a technique, well known, but not widely used for most situations.

CSA is Cross Sectional Area, for a circle is Pi r2 for the Cross Section, for a rectangular or square core: l x w for the Cross Section, this extremely important technique means, as we increase the Area the Coils are exposed to, we need less turns for the same Voltage, as a result we get more Current due to the Coils DC Resistance being much less!

By increasing the area of the Wire Exposed to, or occupying the fluctuating Magnetic Field, Sparky doubled the output. Exact proportions/ratios of Space-Filling Volume of windings to output have not been determined with precision, but a relation is evident.

Ref: Floyd Sparky Sweet - LabNotes

 

Your post is extremely important! I hope others pay attention, learn as much as they can from it!

I hope this helps!

  Chris

Chris posted this 18 March 2019

My Friends,

Delayed Conduction is a very easy way to control the Partnered Output Coils, sensitive to Electric Fields at Time t.

You will notice, The Partnered Output Coils Delayed Conduction Stage is always at a single point:

 

 

In the Area of Power if Voltage and Current are 90 degrees out of Phase, Current Lagging, is a very important place to keep in mind! All machines I have studied have used this area in one fashion or another, Kapandze, the Spark fires at the peak of the Wave, same place. Through a short thick Copper Coil. This interruption in Conduction, Delayed Conduction, is critical.

This Thread shows some circuits, but there is a little fiddling with what actually works. Frequency, Amplitude, Timing, but, the most important thing is: You know now, what to look for!

   Chris

Chris posted this 18 March 2019

My Friends,

For the GOOD in the World!

I want to let you ponder something. Its an important ponderance! Especially in this situation! The Time Bases are all the same:

 

 

Graham Gunderson's Left Side Partnered Output Coil was connected permanently to the Load, Capacitors and Globe:

 

For the entire time, between the Red markers! The Red markers indicate Off Time! Thus the Voltage Spike! Almost 700 volts. The Bottom Purple Line between the Red markers, is 9 Volts on the Capacitors, Conduction, Connected to the Output!

Connection interruption also seen here:

 

A big pixelated mess, but it can ne seen!

@CD - You asked, I wanted to point out, some huge things there for the ones that can see the coming problems!

Question: How did Graham make the Right Side Partnered Output Coil always show the same polarity flip in Current? Why does the Current not Flip the other way sporadically?

   Chris

Chris posted this 18 March 2019

My Friends,

A little speculation with a little evidence:

I believe Graham Gunderson was using Step Switching on the Partnered Output Coils - What Do I Mean?

Two Output Coils, Two Mosfets on the Output. One Mosfet for Each Coil.

In the closeup I showed:

 

 

We see evidence for something which Graham did draw for Reiyuki, who kindly shared all his images. He was present at the conference and took lots of fantastic Images while there, he also asked Graham lots of questions. One Image is shown:

 

With another Image verifying this image:

 

 

My Question:

Question: How did Graham make the Right Side Partnered Output Coil always show the same polarity flip in Current? Why does the Current not Flip the other way sporadically?

 

This is achieved by Step Switching the Output Mosfets as I have just shown. You will only find this information here! Other forums have tied this timing to the Input.

   Chris

Jagau posted this 18 March 2019

Thank you Chris for the correction it is a mosfet no doubt.

It draws the intrinsic capacity of the mosfet so as to understand how the gate fires in relation to the source.
Moreover, he draws the intrinsic diode of the mosfet in a way that I did not know.

We learn every day.


And in addition it gives a little key design not heatink and when you listen well it's the key.


Jagau

Jagau posted this 19 March 2019

Certainly Chris, that's why there is so much confusion in terms of the interpretations,

but most of the time when we look at the manufacturer's dasasheet,

it's the first two on top of the other that we see in datasheet


In addition the IGBT symbol looks like this


Even more confusion with mosfet.


Jagau

Vidura posted this 29 March 2019

Here I post an additional test, I have modified the windings as per Chris' suggestion, primary on the central leg 12 turns, outer legs 36 turns each CW-CCW. Also I have modified the delayswitch as following. the idea is that the 100nf cap charges at the breakdown of the zener and keep the mosfet on until the voltage reverses and resets at the breakdown of the second zener(5.1V)

It seems to work, although the current on the negative halfwave is much smaller than the positive, but with some more adjustments it should work as expected.The setup with a resonant tankcircuit and halfbridge:

and the scopeshot:

Upper trace current, zero is at the second graticulate line from aboth, the voltage zeroline at the middle of the screen.

 

mrblobby posted this 07 April 2019

Absolutely love this series of videos you've been putting together Chris. I really appreciate all the time it must take to put them together. It really helps to explain more comprehensively the principles at work for people like myself. 2 thumbs up.

Chris posted this 10 April 2019

@Atti - Awesome! Very nice!

 

My Friends,

Another video, this time a lot more detail on some things:

 

Apologies everyone. I was referencing a very good video, giving full credit, but YouTube wont allow me to use it for Educational purposes at all.

The video was:

 

Now, isn't this just stupid! I can play the video here, on this page, but cant reference it under the Educational Copyright laws.

I hope this helps some, it took forever to make this. smile

   Chris

Chris posted this 17 April 2019

 

 

My Friends,

Some points I would like to point out, from my last videos:

 

Partnered Output Coils:

 

How the Coils might be placed:

 

  1.  The Primary Coil has a Changing Current, thus a Changing Magnetic Field, which Induces a Voltage on the Secondary.
  2. The Secondary's Voltage will have a Current that is also Changing in Time if a Resistive Load is placed on the Coil.
  3. The Third Coil, the second Partnered Output Coil can be Switched in accordingly, with the detected Voltage on 2.
  4. The Rate, or Timing, in Time of the Switching in, can be adjusted to where the Effects we have described, are seen.
  5. A tunning or adjustment of Frequency and Duty Cycle along with the timing of the switch is important.

 

The difference in Conductivity between the Two Partnered Output Coils creates Magnetic Resonance!

You will see a Triangle Waveform as I have described, when you find Magnetic Resonance.

   Chris

Chris posted this 17 April 2019

My Friends,

I want to share some thoughts I have shared with a Friend wink

 

There is a theme I am trying to share:

 

Any Output Coil with a Resistive Load will have a Phase Angle between the Voltage and Current very close to Zero Degrees. So as long as the Output Coil sees a Resistive Load, then there is no difference between Voltage or Current Controlled Switches.

However, we do often have a Capacitor on the Output, remembering this is used to smooth the Output, this is not a Resonant LC Tank.

The Circuits that can be used are endless, the configurations many, but the ideas that must be followed are very specific.

The basic idea is as follows:

 

 

The Timing of the switch is a factor to be learned for the machine you are building. Input, try what ever you find easiest until you get the best Output.

 

As an example:

The MEG Team used this Circuit:

 

 

Where D2 is a TVS - Voltage Controlled Switch.

With this basic arrangement:

From my early MEG work this version not published until only a few years ago.

 

With this Output Data:

 

I believe the Data is inverted on one or both Axis.

Question: What's required to make The MEG Work?

Answer:

  • Input Voltage Adjustment.
  • Input Frequency Adjustment.
  • Input Duty Cycle Adjustment.

Ask yourself, what happens when the TVS Conducts? L3 is short-circuited right? Maximum Current Flows, and What's this Maximum Current doing to the other Coils? "Generating" Voltages, and also because the other Coils have Loads, they also have a Current, they will be equal and opposite in time when the machine is tuned correctly, we end up with The Mr Preva Experiment Magnetic Resonance. 

We Catch the Wave, we see Magnetic Field interactions within the Machine, that act upon themselves in such a manner to Resonate between themselves.

Its in the way we have been bought up to think, I am sure there is a way of thinking, we have been taught to think in such a way, that does not allow us to see some of these simple things.

   Chris

patrick1 posted this 28 April 2019

Hi,  I just finished my new circuit too test. - , it can;

1.detect a positive voltage and start a timer too determine the delay before conduction,

2.create the conduction pulse, with another timer,   ,    simple right ?...  using 2 breadboards and 6 ics.   lol..!!

does anyone have any tips, assuming a square wave positive offset input. ...   i am more likley too find a sweet spot, by rebounding 90% of the input pulse, or just the last 10% ;-D.....

one other concern i have is that it wont work at all with a positive only offset square wave input. -   perhaps i will need a h bridge.

 

Chris posted this 01 May 2019

My Friends,

As we know, have covered in many places for a long time now, we have an Input Coil that is switched on, as the Current Ramps up / Changes in Time, our Output Coils have an Induced Voltage on then according to Faradays Law of Electromagnetic Induction.

 

 

A Voltage is Induced, and because we have a Load on one Coil, a Current is drawn. Very simple Science. Exactly the same process occurs on the Third, or Second Partnered Output Coil, except this Coil has no Load, no Current is flowing in this Coil, it is Open Circuit.

But, not for long!

The Input Coil's Current Ramps Up like so:

 

 

This indicated, and should be clear now, that we have a Time relationship, the On Time vs the Delayed Conduction Time, we need to find that happy medium, or the sweet spot, were the Input is only on long enough to trigger the process and the Trigger process is fast enough to induce enough Output Voltage, E.M.F = -Ndφ/dt, yes a Transient, time rate of change, to get the Partnered Output Coils working.

In the below Image, the Top Trace, the Input, its short timed, just enough to get the Coils to do their thing!

 

 

 

We switch in the Second Partnered Output Coil, in the form of Delayed Conduction technique, and this is what happens:

 

 

Partnered Output Coils Pump Current, as long as the Potential is high enough:

 

 

Ask any scientist, any Physicist: "Does it cost us anything for Voltage" then ask: "Does it cost anything for Current" - Then ask WHY!!! You will not get an answer forth coming!

We have already covered, Current is MMF, Magnetomotive Force, it must be supported and an Equal and Opposite Current MUST Support it.

All you have to do is start the Pump!

   Chris

 

P.S: Thank You! You are all Awesome!

Chris posted this 02 May 2019

My Friends,

 

A terrible attempt at a Timing Chart! However, the Indicator ( I ) is the Input to the Mosfet ( Q1 ). The Indicator ( O ) is the Input to ( Q2 ). Now Frequency and Duty Cycle will vary, but you get the idea.

Q2 is on for a lot longer than Q1, Q1 is only a Trigger, to get the Potentials up.

 

 

Each and every Coil has one of these, and when timed right, the Magnetic Resonance creates some amazing effects!.

   Chris

Chris posted this 03 May 2019

My Friends,

Time is a critical factor in these configurations! Timing is made easy when we have simple Hardware to make changes in Time easier! Using a Microcontroller, or a simple Circuit, designed to make these changes with the adjustment of a Potentiometer.

REMEMBER: We have proof of the delayed switching of Graham Gunderson's MIT:

 

 

 

 

For new comers, and there appears to be a huge amount from all over the world! Please take the time to read the entire thread and all supporting threads. Its worth your time to make sure you know what the material I am sharing is about!

Don't forget, the Timing of the Conduction of the Output Coils is very important!

Getting this right will give you a machine that "Generates" much more energy Out than you put in!

   Chris

Chris posted this 08 May 2019

My Friends,

I hope, soon, people will understand the significance of my showing this image:

 

 

In combination with my very familiar image:

 

 

These images give you Voltage and Current Polarity, some polarity's that Science may not agree with. Giving you Energy that is in reverse to Current Conventional Energy.

I want to make a special note to all readers, this is more important than anyone can currently realise! Use this in combination with the information recently shown in my videos and in my posts and its very easy, with the right equipment to make a machine that "Generates" a lot more Energy than is input!

   Chris

Chris posted this 13 May 2019

My Friends,

I thought we might had seen a few more experiments on this subject by now. Perhaps even a few Successful replications of the now famous Sawtooth Waveform.

In a few of my very early videos, I referenced the Hydraulic Ram Pump:

 

Careful study shows the action! As the Water rushes down the pipe, it reaches velocity sufficient to snap the Valve shut. This creates a large potential, a large Pressure, and the Water is forced up the second one-way valve not to return. This water is the Water that is pumped. Water is merely the medium used, put under pressure and regulated, where Time is a function of Resonance of the System.

Gravity is the Fuel for this Machine!

Water and Magnetic Flux are very similar in the base methodologies.

In the following MEG Schematic:

 

 

D2 is the Valve that Snaps Shut. Of we have also looked at the following analogy:

 

 

Where the Switch shown represents the Valve! The Valve snaps shut when the Velocity of the water is sufficient. This creates a large Potential, a large Pressure, then as we have learnt, this pressure must return to zero, but it must occur according to a specific Time Constant. This is Magnetic Resonance.

   Chris

Jagau posted this 14 May 2019

Hi Chris

The circuit that you propose above works very well .

in resonance and input impedances adapted  and after peeking and tweeking to the circuit, it gives power.

Jagau

Forelle posted this 14 May 2019

Hi Chris It should only be an another hint that there are several ways to delay the current of course there is a difference between conduction and induction but as you said in the end you could reach the same goal.Some years ago one brings up this patent and called it gabriel device.I know that you know all this stories it is more for theyounger Members so they see there are more ways . Good day.

Chris posted this 20 May 2019

My Friends,

For the sake of rambling, I shall ramble.

As we all know now, a TVS has a break over voltage rating. This rating is where the device starts to become Conductive. A critically important aspect and the point of this and other threads.

Once selected, the TVS Break over Voltage Rating can not be changed.

The only way to make adjustments, is through Frequency Adjustments. If Voltage were equivalent to Rise, then Frequency is equivalent to Run.

 

 

Why do we need to adjust the Frequency?

Good point, I am still, to this day, not entirely sure. I do know that one can not achieve Magnetic Resonance without finding this Frequency point.  I do know this is normally a very short duration. I pointed out, my frequency was the time in-between the H-Bridge switching, between polarities, at 1.2 KHz and this duration is in the region of ‭0.0000014‬ to ‭0.0000003 seconds approximately.

I am guessing, The MEG Team have seen the same thing, if the average TVS is delay time is 1ps from 0V to BR Voltage, then an average time before TVS Break Over Voltage is easily in the order of 0.000001 seconds.  You can see on the Data The MEG Team have us:

 

 

Remembering the Frequency reported by The MEG Team was 31KHz.

Graham Gunderson did say his Switch at the Mosfet was in the order of around 1MHz, which is around ‭0.000001‬ seconds approximately.

Was Alfred Hubbard and the early research done there on the right path? Is this to do with Electron Paramagnetic Resonance ( 2.80GHz ) also pointed out by Floyd Sweet?

 

I think so!

So, to re-iterate, the Delay in Conduction is in the order of ‭0.0000014‬ to ‭0.0000003 seconds approximately.

   Chris

Chris posted this 28 May 2019

In my last few videos, I mentioned the Increase of amplitude when one gets to the point of the above noted Harmonic Interactions. What do I mean by this? Well, from examples gone, lets see if we can find some similarities!

 

My Friends,

I should have also reminded you, as it is not clear in my last post: The Input Excitation is Excited by, Assisted by, L3, the Second Output Coil switching in! The Two MMF's are in the Same Direction, not Opposing!

Where D2 represents a Bi-Directional TVS.

 

So as D2 ( TVS ) Conducts, we have Three Coils with Current in them all at the same time, Two Positive and One Negative, remember our equation: 1 + -1 + 1 = 1?

This is why we must have such a narrow Time ( Rise over Run, X Axis ( Run ) considered to be Time ) as mentioned above. In the above Schematic, as D2 Conducts, we are able to Trick, or Fool the L3 Coil into assisting the Primary, this is why we have such a fast Rise Time. MMF is greater in the Forward Direction by almost two thirds! I have used the term and we have a Thread for this: Non Linear Inductance and also Parametric Excitations of Electric Oscillations.

We have Reduced impedance Effect on the Up and also Down Sides of the Sawtooth Waveform. Remember, our Input is reduced by this effect, we move from using Current, to using nearly No current or even Negative Current, remember what we spoke about.

We must Counter Balance Our Input Force, or M.M.F: Magneto Motive Force.

This is all such important stuff, please do the best you can to study, PM me any questions!

   Chris

patrick1 posted this 29 May 2019

My work with ferrites has yeilded poor results, which is a shame, - they are still in my sights for the future, because i think i can make them work eventually, however it will require a raspberry pi or similar

but for the time being, i have found iron cores the best too work with, - as it happens, i am currently 3d printing some new spools, for a new transformer, - the transformer, is basically.  or exactly...  a MOT with 2/3 of the lamination's removed,-     i think the best results at this stage will come via this approach, - i know im only nickle and dimeing, but this technology has marginal COP's - - can anyones core material or origins beat the COP 1.5 i think i can manage with mine ? what kind of material are you using ?

Topic Is Locked

We're Light Years Ahead!
Our Above Unity Machines:

Asymmetrical EMI

Wistiti's Bucking Joule Thief
Non-Inductive Coil Experiment
CD's Non-Inductive Coil Rep
Baerndorfer's Experiment
Captainloz's A-R-E
Aetherholic's COP>4.0

Resonant EMI

Yo's Ferro Resonance
Jagau's Non-linear Resonance
Ferrite at work
Recomended Protocol:
Measurement
Switching System
Measurement Block
Current Observation
Current Sensing Resolution
Members Online:

No one online at the moment

What is a Scalar:

In physics, scalars are physical quantities that are unaffected by changes to a vector space basis. Scalars are often accompanied by units of measurement, as in "10 cm". Examples of scalar quantities are mass, distance, charge, volume, time, speed, and the magnitude of physical vectors in general.

You need to forget the Non-Sense that some spout with out knowing the actual Definition of the word Scalar! Some people talk absolute Bull Sh*t!

The pressure P in the formula P = pgh, pgh is a scalar that tells you the amount of this squashing force per unit area in a fluid.

A Scalar, having both direction and magnitude, can be anything! The Magnetic Field, a Charge moving, yet some Numb Nuts think it means Magic Science!

Start Here:
Help with using the Forum.
Message from God:

Hello my children. This is Yahweh, the one true Lord. You have found creation's secret. Now share it peacefully with the world.

Ref: Message from God written inside the Human Genome

God be in my head, and in my thinking.

God be in my eyes, and in my looking.

God be in my mouth, and in my speaking.

Oh, God be in my heart, and in my understanding.

Your Support:

More than anything else, your contributions to this forum are most important! We are trying to actively get all visitors involved, but we do only have a few main contributors, which are very much appreciated! If you would like to see more pages with more detailed experiments and answers, perhaps a contribution of another type maybe possible:

PayPal De-Platformed me!

They REFUSE to tell me why!

We now use Wise!

Donate
Use E-Mail: Chris at aboveunity.com

The content I am sharing is not only unique, but is changing the world as we know it! Please Support Us!

Thank You So Much!

Browse by Category:
Weeks High Earners:
The great Nikola Tesla:

Ere many generations pass, our machinery will be driven by a power obtainable at any point of the universe. This idea is not novel. Men have been led to it long ago by instinct or reason. It has been expressed in many ways, and in many places, in the history of old and new. We find it in the delightful myth of Antheus, who drives power from the earth; we find it among the subtle speculations of one of your splendid mathematicians, and in many hints and statements of thinkers of the present time. Throughout space there is energy. Is this energy static or kinetic? If static, our hopes are in vain; if kinetic - and this we know it is for certain - then it is a mere question of time when men will succeed in attaching their machinery to the very wheelwork of nature.

Experiments With Alternate Currents Of High Potential And High Frequency (February 1892).

Close