Chris's replication of Andrey Melnichenko's GLED

  • Topic Is Sticky
  • 1.6K Views
  • Last Post 30 July 2020
Chris posted this 13 February 2020

My Friends,

I am going to have a go at replicating the GLED of Andrey Melnichenko.

If this project helped you, please consider a Donation:

Donate (PayPal)

Donate (Patreon)

 

Please Note: My work, shared here: Chris's Non-Inductive Coil Experiment, is related to, the same concepts as, this work. But my experience outside of what I have shown you is limited. I have worked on this before, but it was a long time ago, and on a breadboard:

 

I am re-replicating this experiment for my own and others benefit. No guarantees here guys, ok. Lets just do our best here. I am sure we can do it again wink

Some history behind the GLED, first designed and shown by Andrey Melnichenko and friends back around 2000. Some videos exist, the face of the person holding the GLED is Arthur Tränkle, currently the CEO of Steho Energy:

 

We have a thread here: Akula's circuits- is this the principle? that also has a LOT of information on this device! Its worth going and studding that thread also!

Akula, Roman Karnouhov, replicated the GLED and never gave Andrey Melnichenko any credit for it! Akula, Roman Karnouhov, did post this to the realstranik forum:

All schemes to develop and execute on principles of operation (Transgenerator magnetic field Andrey Melnichenko) and what to do with Pantyuhavu have!

 

Some months after the replication, Roman Karnouhov started working for Arthur Tränkle, and Steho Energy:

 

The Video Transcript:

they don’t burn, but we have a voltage going on here goes 19 hertz 19 hertz is going on I'm not talking about what signals of their time and about his time about everything else I have no right we go to this spoon 1910 the power goes 2 and 6 volts and what do we see in our coils in our coils we see here the signal that the vadik showed, but I have it a little stronger since I’m just not the first time to assemble this design with a similar design so I have more serious fronts, that is, we feed 2 and 6 volts and we see that the pure moreover, we supply 2 and 6 volts and a frequency of 19 hertz, but this the transistor and what we see undamped oscillations, our coil, together with pyrite, it buzzes and at a cleanliness of 293 it becomes a little wrong this is 290 kilohertz here are our non-damped oscillations, that is, this is the beam now it’s on the collector then on the collector of this transistor it’s just we see our 19 hertz the whole set of work of the ether of a given coil design in automatic undamped oscillations oh well, now I think I’ll show the operation of the voltage, that is, now I will increase the supply voltage to That operation of our voltage stabilizer before they work on the diodes light up, that is, you can now add a little bit so 2 of 6 here are 2 and 6 and our LEDs are on, they light up and two of our undamped oscillations became even more than 10 volts here on the collector undamped oscillations with the frequency of the resonance firm and the overall design turned out to be 10 volts, that is, in principle, the record itself can now be made even without this generator, well, it is necessary for stabilization, since we have a load, there are nights, I can say wadik For you, but great successes, good luck, I’m glad that in just about a year and a half I see a person who with his own mind reached it with his own hands, launched the scheme, was able to stabilize this process and get the scheme so-called free energy, I won’t even collect the scheme for all unbelievers and bitches can consult with the author, he will tell you that this is the true work of this device to tell you more too I have no right do not be offended by all the questions to the author of this scheme, but a very original solution is generally very original Inalnaya, but only with this original solution we need to slightly change the design, that is, Vadik I can say for sure because this is not the first time I have assembled this design for such power and there are two but three LEDs in which your mistake was, it’s purely you will understand only you were the mistake in that you have two LEDs, but I didn’t actually consider it, maybe I didn’t see it, I don’t know, but I couldn’t turn up the power because you had two LEDs in parallel, you need to sequentially and here, at the output, raise a little voltage yes, of course, your return line will start up well and that’s all, but also what can I say? This is a microcircuit of working with this transistor that eats a lot, just eats the power of one of the LEDs, that is, it can be replaced with a simple multivibrator, it will be much more economical to form of what is needed here precisely with this generator, well, guys, see the free energy, he’s so very glad I’ll be talking with you, maybe even work together so that you don’t see something I even know a new share something very glad I will talk to you and indeed to discuss something interesting for the future, we

 

 

The Video Transcript:

so well, what’s happened, I’ll show it’s most interesting, it’s not loving now, it’s not working at all yet, I haven’t completely caught up with all the signals, tested the working principle of forming a low-frequency resonance in seconds, that is, our face of cultures is output and this capacitor is what we have here it is here it is so here we have a series of bursts of pulses from them we see the low-frequency component and what’s actually looking for this thing is f**king erase three monsters I’ll rewind the general resonance of the fer Rita does not match for the formation of a low-frequency sinusoid I can’t raise the power then you have it for the last time I’ll be holy he would understand now we are looking for this one now it works like this

 

Observing the approximate lengths, where each unwind is approximately an arms length, about one meter, we get the following lengths:

23 arm lengths

26 arm lengths

 

I have a Pot Core, one that you have seen before:

 

I have drawn the circuit and have the following design:

 

This is just a start. Any changes / improvements will be incorporated and a new circuit may be shown at a later date. This is a copy of Akula's Circuit:

 

Which was a copy of Andrey Melnichenko's Circuit:

 

I have replicated this before, on the breadboard. I have had some successes with this circuit, but I thought I would make this a bit more evolved to show others. To try to help others advance! However, I can only do so much, I cant do it all for you! You need to so this for yourself!

 

Equal and Opposite

I am going to continue harping on about the basics: Equal and Opposite!

NOTE: The above schematic from Akula, he drew with pen, big dots, above. Each dot is a Test Point, where the Oscilloscope measures the Voltage at each point.

NOTE: The AC Voltage is equal and Opposite:

 

Also Note: The bottom waveform has a goodly degree of DC Offset!

 

PCB Give Away:

I have some PCB's to give away, you pay for postage, from Aus to most parts of the globe its about 8 - 10$. PM Me and I will pick some lucky recipients! Its just a bare bones PCB, you purchase the components and fit as a kit for yourself.

I have most of the components already. I have the PCB's on order and they should be here in a few days.

   Chris

Order By: Standard | Newest | Votes
Captainloz posted this 07 April 2020

Hi Chris,

I little more progress. Just playing around to see the circuit working on the scope. I'm still waiting for my bobbin to arrive.  Will post another video once I get it done.

Cheers,

Loz

 

Chris posted this 14 February 2020

My Friends,

Here is the Circuit I drew:

 

I copied Akula's Circuit:

 

Its a start, and what I based my last experiments on. It may change at any time.

   Chris

Jagau posted this 14 February 2020

This little circuit is very unifying, we have to revise several things that we have to share and learn over time

and that will help us understand how we have reached more than 1 unit.


I believe that many will like to reproduce this circuit.


Jagau

Chris posted this 02 March 2020

My Friends,

I have a little progress on the PCB:

 

Still a work in progress as you can see.

Best wishes,

   Chris

Captainloz posted this 28 March 2020

Hey Chris,

I got side tracked with this. I just couldn't resist. Making a little headway, just waiting on parts to finish. Looking forward to experimenting with it!  Cheers mate

Loz

 

Jagau posted this 12 May 2020

The low frequency component is present only when the 2 copper strips are connected to the first coil only, they act as capacitors and magnetic gap. To have tried different mounting this one is the most effective to date. The lowest voltage and power obtained is from 2.03 volts as you will see in the video.

 

Work remains to be done to increase the low frequency to around 270 hertz, then adjust the mosfet which should act as a pump recharging the primary capacitor in order to produce a selfrunner.

Jagau

Jagau posted this 10 May 2020

Hi chris and captainloz
I did with you for this beautiful project.

Connect on P.S.


After mounting the components and winding up the potcore I got this figure on my oscilloscope.

 

Compare to Akula

The frequency of the bottom is not good it is only 37 kertz I think Akula had 269 so it's not finished.

The CD4069 with this photo on the mosfet gate 2n7000 (down waveform) but it is too slow and too dirty so work to do on this side.

the precise operating voltage is 2.74 volts


Tell me how you made this circuit and what kind of figure you got so that we can combine our efforts.

You have made a great board Chris, thank you

Jagau

Chris posted this 07 March 2020

Hi Chris, could you post details about the integrated circuits used and about the characteristics of the LEDs?

Thanks.

 

Hey Fighter,

Yes, of course. this is a basic parts list:

 

I copied from this circuit:

 

The MC34063 Datasheet is here. The CD4069 Datasheet is here. Just use any LED's you want, I use 10mm White LED's and shave a little off one side, so they fit to the PCB, I have a very tight fitting PCB designed.

I hope this helps!

Best wishes,

   Chris

Chris posted this 07 April 2020

Hey Loz,

Nice Work! Thanks for sharing!

I need to get back to work on mine! Finish it off.

Best wishes,

   Chris

Captainloz posted this 29 July 2020

Hi Guys,

I'm so far behind on this thread. I have this video to share however I'm not sure if it's much help to anyone.  It's really just the start.  I feel bad that I haven't been able to contribute lately.  Hopefully in two more weeks I'll be able to spend more time on this, and really contribute something substantial.   

Beautiful work Jagau!  Thanks for sharing! 

Cheers,

Loz

 

Chris posted this 30 July 2020

Hey Loz,

Nice work My Friend! Good to see your'e back with us! 

I enjoyed my replication on this device. I will post more soon. Yes Jagau has a very nice waveform, its all right with Akula's original machine:

 

Akula when he shared his work was very informative, very useful! Remember this is all a copy of, a replication of, Andrey Melnichenko's GLED.

The Coil Interactions are hidden partly by the Circuit Operation, but we do have Coil Opposition between L1 and L2.

The Diode D1, is a Current Blocking Diode, ensuring Current flow in one specific direction! The same as I used in my Non Inductive Coil Experiment.

The basic operation is the same, even though the wave shapes are different. Your experiment here uses the same basic function to make this work. 

A few things to try to make this self run:

  • Drop the Input Voltage.
  • Swap the Coils over, L2 = L1 and L1 = L2.
  • Swap the Terminals of one coil only, the Polarity.
  • Add more turns to L2 (54mH) or remove turns from L1. (22mH)

 

Great work My Friend, its great to see your video! Thanks for sharing!

Best wishes, stay safe and well My Friend!

   Chris

Fighter posted this 07 March 2020

Hi Chris, could you post details about the integrated circuits used and about the characteristics of the LEDs?

Thanks.

Chris posted this 04 April 2020

Hello and welcome Jynx!

Thank You!

As far as I know, yes, Andrey Melnichenko, and his team, were the first on the GLED. I can find no evidence to show anyone else was before him!

The Top Rail shorting, is L R C Resonant, so the Coil ( L ), the Resistor ( R ) and Capacitor ( C ) have a time constant that can be calculated, the time constant being in seconds, and 1 / s = Frequency. The Shorting is the cause of the Sinusoidal wave forum you see here:

The Video here:

 

Once the GLED is in operation, the Sinusoidal Waveform is part of the function of operation. Its required. This does not mean once you get this waveform its selfrunning, it means its the start! More work may be required.

Sometimes you may be required to swap the Coils over, from terminal to terminal, also possibly polarity.

Best wishes,

   Chris

Chris posted this 10 May 2020

Hey Jagau,

Very nice, awesome work! Thank You for Sharing!

You have shown whats possible with an hour or so work! Very nice! Thank You for Sharing! I have been here before, this is where a little time can be involved, in getting the machine to run better, and getting it to go Above Unity.

Optimizing the interactions between the Coils and making sure the right polarity is involved, then this machine can run itself.

 

 

He always did refuse to put inside a Faraday Cage, I asked on many occasions, he did not, only claiming Radio Station was powering it, the problem could have been very easily resolved if he had listened. 

This was shown in the original Videos: Video 2

 

 

Most of the work is done my friend! Very nice to see! Congratulations!

Best wishes, stay safe and well,

   Chris

Chris posted this 12 May 2020

Hey Jagau,

Beautiful Work My Friend! Very nice! Thank You for Sharing!

Best wishes, stay safe and well My Friend!

   Chris

Jynx posted this 04 April 2020

Hello guys. My first post here. Nice work on the circuit boards. I have been reviewing the GLED schematics and have a question. Was Andrey Melnichenko the first to do an eternal led lantern? What is the purpose of using the mosfet to short the power supply rail to ground through the resistor?  The Akula schematic does the same thing. 

Jagau posted this 11 May 2020

Hi chris


Sorry , but but I do not use any reference signal like this guys does to produce this image in all his Utube that you showed. 

What I posted here. It is neither a montage nor a fake.

The image you saw is very real and is produced only by the way the potcore was made and no function generator connected,.
I'm going to make a video instead of a photo to demonstrate it, you can judge for yourself what I did. I would never dare to fool people here,

I think it's a serious forum here at least that's what I think.

Jagau

Chris posted this 11 May 2020

Hi Jagau,

Your work is very impressive! I know your'e very talented in Electronics!

I know your work is genuine and very real! So please don't take my post the wrong way! What I shared is only for reference for others, I am not questioning your work!

I hope we do not misunderstand each other, I hope I did not say anything that has offended you!

 

Some Background:

TinselKoala is very good with Electronics, he used to badger me, to say it nicely, and now it's my turn to show him how serious we are about this.

 

Please don't take my post the wrong way! I know whats achievable so you have my full support here! I hope others can also see whats achievable! I hope others can see what this is all about, and how serious we are about this! For example, getting professionally made PCB's to make all this work so in the public eye, we are seen as professionals!

Jagau, I have the greatest respect for you and your work! It is great to see such impressive work!

I only referenced TinselKoala's work for others to see what we are doing, and how serious we are!

I would very much appreciate a Video that would be great! Thank You for sharing!

Best wishes, stay well,

   Chris

Members Online:

No one online at the moment

Since Nov 27 2018
Your Support:

More than anything else, your contributions to this forum are most important! We are trying to actively get all visitors involved, but we do only have a few main contributors, which are very much appreciated! If you would like to see more pages with more detailed experiments and answers, perhaps a contribution of another type maybe possible:

Donate (PayPal)

The content I am sharing is not only unique, but is changing the world as we know it! Please Support Us!

Donate (Patreon)

Thank You So Much!

Weeks High Earners:
The great Nikola Tesla:

Ere many generations pass, our machinery will be driven by a power obtainable at any point of the universe. This idea is not novel. Men have been led to it long ago go by instinct or reason. It has been expressed in many ways, and in many places, in the history of old and new. We find it in the delightful myth of Antheus, who drives power from the earth; we find it among the subtle speculations of one of your splendid mathematicians, and in many hints and statements of thinkers of the present time. Throughout space there is energy. Is this energy static or kinetic? If static, our hopes are in vain; if kinetic - and this we know it is for certain - then it is a mere question of time when men will succeed in attaching their machinery to the very wheelwork of nature.

Experiments With Alternate Currents Of High Potential And High Frequency (February 1892).

Close